Procedure Table Height & Access Guide: Bolt 5000S vs. Bolt 2000 Podiatry
A procedure table needs to fit both the clinician’s working position and the patient’s approach. If you are a shorter clinician or regularly treat older patients, start by checking the lowest position, then test the full workflow. Height range alone does not establish comfort, transfer suitability, or accessibility compliance.
Compare the verified specifications
| Specification | Bolt 5000S | Bolt 2000 Podiatry |
|---|---|---|
| Published height range | Flat: 20–34 inches | 20–36 inches |
| Separate upright dimensions | Published upright chair height: 48–57 inches; not a verified seat or transfer-height range | No separate upright height range listed |
| Published length | 77 inches flat; 66 inches upright | 73 inches |
| Width with armrests | 32 inches | 34 inches |
| Width without armrests | 23.6 inches | 25 inches |
| Base dimensions | Confirm before room planning | 39.5 inches long × 21.5 inches wide |
| Listed weight capacity | 400 lb | 440 lb |
| Electrical specifications | 110 V | 100–120 V, 50–60 Hz, 200 W |
Both models list a 20-inch minimum. The Bolt 2000 Podiatry reaches 36 inches, 2 inches above the Bolt 5000S’s 34-inch flat maximum. The 5000S’s published 48–57-inch upright chair height is a separate dimension: do not use it as the patient seating height or compare it directly with the flat working range. Confirm the measurement reference points before ordering if a precise transfer or treatment height is essential.
Fit the table to standing and seated workflows
There is no single table setting that fits every clinician of a given height. The procedure, patient position, stool height, footwear, and reach all affect fit.
- Standing work: Test your usual treatment position with shoulders relaxed and without sustained bending or reaching. Check access at the head, sides, and foot end. Shorter clinicians should specifically test whether the 20-inch minimum and intermediate settings support their work.
- Seated work: Use your normal clinical stool and check sight lines, foot support, knee clearance, and access to controls. A low table setting does not automatically mean the base or upholstery provides sufficient leg clearance.
- Position changes: Rehearse moving between examination, treatment, and entry or exit positions. The 5000S lists a 240-degree swivel; include its movement in the room test. The 2000 Podiatry lists height, backrest, footrest, and seat-inclination adjustment.
Before choosing, arrange a demonstration or confirm critical measurements with Bolt Medical Tables. Test the actual procedure position rather than selecting from clinician height alone.
Plan patient approach and transfer
A 20-inch minimum is a useful planning measurement, not a guarantee of an easy or safe transfer. For older patients or people using mobility aids, assess the individual’s needs and follow your facility’s transfer procedures.
- Confirm the actual patient-support surface height in the intended entry or transfer configuration, including upholstery and positioning.
- Compare that surface with the patient’s wheelchair or other transfer surface where relevant. Do not assume the listed minimum creates a level transfer.
- Check the approach side, clear floor space, armrest position, and room for staff or any transfer equipment used by your facility.
- Both product listings describe movable or removable armrests. Confirm operation, restrictions, and the appropriate transfer configuration in the model’s instructions.
- Rehearse entry and exit with qualified staff, and confirm the table’s capacity and operating instructions before use.
Measure the room, not just the table
Start with the published dimensions above, then allow for the complete movement of the backrest, footrest, headrest, armrests, and any swivel. The 2000 Podiatry’s base dimensions are not its full operating footprint. Published table length and width alone do not establish a minimum room size.
- Measure doorways, delivery turns, and the route into the treatment room.
- Mark the table footprint on the floor and check clinician access in both seated and standing positions.
- Allow for patient approach, staff assistance, stools, carts, mobility aids, and transfer equipment.
- Check moving parts against walls, cabinetry, and other equipment through the full intended range.
- Confirm the required clearances and final room layout with your facility team before purchase.
Check power access
The Bolt 5000S lists 110 V. The Bolt 2000 Podiatry lists 100–120 V, 50–60 Hz, 200 W. Confirm the current model’s plug, grounding, circuit requirements, cord length, and installation instructions before planning the outlet location. Keep the power route clear of patient approach paths and moving components, following the manufacturer’s instructions.
Which model should you evaluate first?
Evaluate the Bolt 5000S Medical Procedure Table with Stirrups first if stirrups and swivel are important to your procedure workflow, and test its 20–34-inch flat range.
Evaluate the Bolt 2000 Podiatry Procedure Table first for a podiatry workflow or when the listed 36-inch upper height is useful. Both models still require a real-world fit and transfer assessment.
You can also browse the collection titled ADA Compliant Tables. The collection name is not a determination that a model or room setup meets accessibility requirements. This guide compares published specifications and practical planning considerations; it makes no accessibility or regulatory compliance claim.
Before ordering, confirm current specifications, measurement reference points, room clearances, and transfer requirements with Bolt Medical Tables and your facility team.